ADVISORY: Apologies but our phone system is down. For booking enquiries, please message us online.
We make old floors like new again!
*All quotes shall incur a $50 fee that shall be deducted from the cleaning costs if you proceed with the quoted work or another Electrodry service. Read the complete terms and conditions.
Proud ATFA Member
Electrodry is a proud member of the Australian Timber Flooring Association.
Non-Toxic and Odourless
We use water-based floor coatings that are non-toxic and odourless.
Dust-Capturing System
Say no to sanding dust with our unique dust capturing system!
Finished in Just 2 Days
We finish most jobs within 2 days, and the floors are ready to walk on the next day!
Scratch-Resistant Coatings
Scratch-resistant coatings to keep that new-floor feeling for longer!
Your Choice of Finish
Have the finish of your choice, may it be gloss, satin, matte or ultra-matte.
Call our hotline 13 27 13 or schedule a quote and pre-inspection online.
During the visit, our technician will tell you the cost, likely results and answer all your question.
Book with peace of mind knowing exactly what to expect on the day of your service.
We charge a $50 quote fee which is later taken off the total charge when you book any Electrodry service. An on-site visit ensures that our quote are all inclusive, so there will be no hidden surprises.
wood floor serviced since 2017
A proud ATFA member
5-Star Rated Service on Feefo
Timber Restore uses a deep clean process combined with a special polyurethane coating to refresh and to breathe new life into dull, tired floors. After timber restore your floors will look so good you won't believe your eyes.
We start by giving the area to be sanded a thorough clean and punching nails deeper into the boards where required.
We sand the floor with a weighted rotary sander, which removes less timber than a belt sander, so your floor will last.
We continue sanding, using progressively finer grades of sandpaper to remove scratches and discolouring, and give your floor a clean finish.
Next,sand the edges with a hand held rotary sander, with a final sand using orbital sander to leave a smooth, scratch free finish.
We will then apply a water-based primer to prepare it for coating. If required, we can follow this up with a thin coat of a desired toner.
The last step is applying two coats of a high density, two-pack water-based polyurethane for a durable finish.
In 2021, Electrodry refinished more than 2000 wood floors. We are the only company in Australia that provides non-sanding wood floor refinishing services (see our Timber Refresh and Timber Restore services). This means we can provide you with a range of options to refinish your floor that suit your circumstances and budget.
A weighted rotary sander takes off less wood in the sanding process and enabling us to refinish delicately engineered timber floors without the risk of causing damage. When sanding your floor, we always use at least 3 grades of sanding discs (coarse, medium and fine) to give the cleanest possible finish without sanding scratches or sanding swirls.
The cost varies between cities and states and will vary depending on the state of the floor and work required. If you would like a table of charges please call Electrodry on 13 27 13 or contact us online.
Our 14-day satisfaction guarantee ensures your peace of mind. We address concerns promptly, free of charge, based on valuable customer feedback. Rest assured, we take action to resolved any quality issues identified in surveys.
ELECTRODRY'S COMMITMENT TO QUALITY
There’s not too much to take care of. You will need to remove all furniture and personal items from the rooms that we will be sanding. If you would like to leave very heavy items in place such as your fridge, we can work around these.
Small jobs, such a single room, can be completed in a day. Medium size jobs (up to 75 square metres) will usually be completed in two days but may require three. Time frames for larger jobs will depend on the size of the job and the work required. Your technician will be able to give you a time frame when they inspect the job. Staining will increase the job time by 24 to 48 hours, depending on the size of the job.
Your floor will be ready to walk on the following day, although we recommend just walking in socks for the 36-48 hours. Furniture can be replaced the following day, providing new furniture pads are placed under your furniture to prevent scratching. Heavy items with wheels such as furniture trolleys and fridges must be kept off the floor for 1 week. The same applies to floor coverings such as rugs.
Electrodry uses skilled 2 man crews (no junior apprentices) and rapid curing two-pack floor coatings that allow us to apply multiple coats of polyurethane to your floor in a day. This is in contrast to other floor sanders who often use a technician and a junior apprentice and apply two or three solvent-based coatings over two or three days.
If the area to be sanded does not include vital rooms such as bedrooms and kitchens, then it may be possible for you to stay in the house. However it is important that the rooms being sanded are completely free of traffic, so you won’t be able to access them during the sanding process. If you are considering staying in the house, keep in mind that you may find the noise unpleasant. It is especially recommended that if you are pregnant or suffer from asthma that you find alternative accommodation while we are working on your floors.
Electrodry uses high-quality two-pack water-based floor coatings with rapid curing times and minimal odours. In most cases you will struggle to detect an odour four hours after the completion of the job, meaning there will be no odour when you start using your freshly sanded rooms.
Electrodry uses a dust capture system that collects the great majority of dust we produce. You may find a light film of dust on some surfaces in areas where we are sanding, but we will wipe down these surfaces as part of the job.
We can sand out most damage to your wooden floor. However, some pre-existing issues may remain or could affect the final finish of your floor. These include:
Deep cuts in your floorboards (from carpet trimming knives, for example). This is because sanding out deep damage would require sanding the boards to a dangerously thin level.
Water Damaged or weathered floorboards may require replacing or may affect the even-ness or tone of the final result.
Urine damaged floor will have dark stains that may remain.
Electrodry Adelaide provides floor sanding and polishing services for hardwood and engineered wood floors. Engineered floors have a 2 – 3mm timber veneer over MDF board, that can be safely sanded using our rotary sanding process.
Call us on 13 27 13 to talk to us about your floor sanding needs.
Electrodry’s Timber Refresh and Timber Restore are great options for floors that have small scratches, are worn, discoloured or have a build-up of grime and cleaning solutions. These services are one-day options, and can give you a brilliant finish for a smaller cost than sanding. But for some floors, these services won’t be enough. We want to give you all the options to get your floor looking great again, and sanding is an important part of that! Electrodry Wood Floor Sanding is the best option when your floor is significantly scratched, unevenly worn, or just needs some serious work to have a new lease on life. See our Wood Floor Refinishing page for a full comparison.
Ask Us
